32 s&w long starting load
4 posters
Page 1 of 1
32 s&w long starting load
I will be picking up my Hammerli sp20 pistol whenever the chief of police gives his ok.
My question is i am looking for a starting load with a 89 grain wadcutter. At this point all i am looking for is a load that will work the action so i can have some fun the first time out. I only compete against myself at this point in my life because of age and medical issues. i can work on accuracy loads next time. For powder i have bullseye red dot green dot accurate #2 Winchester 231. thanks Joe G
My question is i am looking for a starting load with a 89 grain wadcutter. At this point all i am looking for is a load that will work the action so i can have some fun the first time out. I only compete against myself at this point in my life because of age and medical issues. i can work on accuracy loads next time. For powder i have bullseye red dot green dot accurate #2 Winchester 231. thanks Joe G
grizzly10x22- Posts : 5
Join date : 2022-10-14
Age : 76
Location : yakima valley washington state
Re: 32 s&w long starting load
1.7 bullseye, tight crimp and go have fun
10sandxs- Posts : 972
Join date : 2016-01-29
grizzly10x22 likes this post
Re: 32 s&w long starting load
Thanks a lot i was not sure and was thinking of trying 1.5 gr but flat was not sure. i will use the 1.7 load as i want the action to work. i am really looking forward to playing with it. joe g. Eastern Washington state
grizzly10x22- Posts : 5
Join date : 2022-10-14
Age : 76
Location : yakima valley washington state
Re: 32 s&w long starting load
Greetings,
Be aware that the SP-20 has either a Standard Recoil Spring or a Heavy Recoil Spring.
The Heavy one works well with ammo around 730 FPS and above.
Heavy Recoil Spring
Softer ammo, 700 FPS or lower, works well with the Standard Spring set.
Also, keep an eye on the small buffer inside the frame. If it is the old metal one, they fail. The newer design is a two piece plastic/foam arrangement.
Buffer Housing
Buffer
Last, do not tighten the grip screw too much. It attaches to the trigger housing and if torqued to high it will break through. Finding a new housing will be challenging.
The links are from Judith Billharz's website. It appears she will ship to the USA again. It is costly; but, she has the parts. Note that they have Walther part numbers. Walther bought the Haemmerli brand a while back.
First place to source parts is Red Feather Outfitters in the USA.
Red Feather
Cheers,
Dave
Be aware that the SP-20 has either a Standard Recoil Spring or a Heavy Recoil Spring.
The Heavy one works well with ammo around 730 FPS and above.
Heavy Recoil Spring
Softer ammo, 700 FPS or lower, works well with the Standard Spring set.
Also, keep an eye on the small buffer inside the frame. If it is the old metal one, they fail. The newer design is a two piece plastic/foam arrangement.
Buffer Housing
Buffer
Last, do not tighten the grip screw too much. It attaches to the trigger housing and if torqued to high it will break through. Finding a new housing will be challenging.
The links are from Judith Billharz's website. It appears she will ship to the USA again. It is costly; but, she has the parts. Note that they have Walther part numbers. Walther bought the Haemmerli brand a while back.
First place to source parts is Red Feather Outfitters in the USA.
Red Feather
Cheers,
Dave
fc60- Posts : 1459
Join date : 2011-06-11
Location : South Prairie, WA 98385
Re: 32 s&w long starting load
thanks a lot. the pistol came with extra springs but i have no idea how to tell them apart. i dont actually have the pistol as waiting for chief of police to say i am not a mass murder question how do i tell them apart for heavy and light. thanks
grizzly10x22- Posts : 5
Join date : 2022-10-14
Age : 76
Location : yakima valley washington state
Re: 32 s&w long starting load
Use caliper and measure the recoil spring wire diameter. Smallest diameter obviously the lighter spring.
Jon
Jon
Jon Eulette- Posts : 4399
Join date : 2013-04-15
Location : Southern Kalifornia
Similar topics
» Starting to load 9mm…. Something weird
» Salyer RO 45 acp starting point / load recommendations
» Load question on Penn Bullets for Distinguished load
» Hornady Lock-N-Load AP vs Lee Load Master
» 32 Revolver Load for long line
» Salyer RO 45 acp starting point / load recommendations
» Load question on Penn Bullets for Distinguished load
» Hornady Lock-N-Load AP vs Lee Load Master
» 32 Revolver Load for long line
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum