Bullseye-L Forum
Would you like to react to this message? Create an account in a few clicks or log in to continue.

One for the Gunsmith's

+4
james r chapman
Jon Eulette
Chris Miceli
Skid
8 posters

Go down

One for the Gunsmith's Empty One for the Gunsmith's

Post by Skid 10/3/2018, 11:45 am

My question is when your going to replace the slide stop on my Range Officer with a oversize one will the replacement just slide right in ( I haven't bought one yet) or do you have to open up the hole up on the frame and link, and if you do what size drill bit or reamer do you use.  Thx

Skid

Posts : 282
Join date : 2014-05-19
Age : 62
Location : Northern Lower Mi

Back to top Go down

One for the Gunsmith's Empty Re: One for the Gunsmith's

Post by Chris Miceli 10/3/2018, 11:57 am

just slide right in

Chris Miceli

Posts : 2715
Join date : 2015-10-27
Location : Northern Virginia

Back to top Go down

One for the Gunsmith's Empty Re: One for the Gunsmith's

Post by Jon Eulette 10/3/2018, 12:04 pm

The 0.200” pins drop in. The 0.203” pins require reaming the frame holes. The link is typically unaffected.
Jon
Jon Eulette
Jon Eulette

Posts : 4399
Join date : 2013-04-15
Location : Southern Kalifornia

Back to top Go down

One for the Gunsmith's Empty Re: One for the Gunsmith's

Post by james r chapman 10/3/2018, 12:36 pm

On my RO the .200 is a close fit,a 201 Gage pin won't go.
james r chapman
james r chapman
Admin

Posts : 6372
Join date : 2012-01-31
Age : 75
Location : HELL, Michigan

Back to top Go down

One for the Gunsmith's Empty Re: One for the Gunsmith's

Post by ric1911a1 10/3/2018, 1:13 pm

Jon,

Which would you recommend for a 9MM stainless Range Officer?

Thanks.

Ric
ric1911a1
ric1911a1

Posts : 338
Join date : 2013-05-07
Location : Upstate NY (the good part)

Back to top Go down

One for the Gunsmith's Empty Re: One for the Gunsmith's

Post by Chris Miceli 10/3/2018, 1:22 pm

ric1911a1 wrote:Jon,

Which would you recommend for a 9MM stainless Range Officer?

Thanks.

Ric
http://www.egwguns.com/1911-parts/egw-heavy-duty-slide-stop-machined-from-barstock-.200-9mm-blue/

Chris Miceli

Posts : 2715
Join date : 2015-10-27
Location : Northern Virginia

Back to top Go down

One for the Gunsmith's Empty Re: One for the Gunsmith's

Post by Jon Eulette 10/3/2018, 2:26 pm

ric1911a1 wrote:Jon,

Which would you recommend for a 9MM stainless Range Officer?

Thanks.

Ric
Ric,
EGW 0.200 SS
Jon
Jon Eulette
Jon Eulette

Posts : 4399
Join date : 2013-04-15
Location : Southern Kalifornia

Back to top Go down

One for the Gunsmith's Empty Re: One for the Gunsmith's

Post by Skid 10/3/2018, 4:46 pm

Thanks all

Skid

Posts : 282
Join date : 2014-05-19
Age : 62
Location : Northern Lower Mi

Back to top Go down

One for the Gunsmith's Empty Re: One for the Gunsmith's

Post by rich.tullo 10/3/2018, 7:05 pm

I tried one on mine it was a little snug on a brand new gun. After 500 rounds its fine, try it.
rich.tullo
rich.tullo

Posts : 2006
Join date : 2015-03-27

Back to top Go down

One for the Gunsmith's Empty Re: One for the Gunsmith's

Post by 10sandxs 10/4/2018, 12:30 am

Jon, Where do you get 0.203 pins?  They might come in handy every now and then...

10sandxs

Posts : 972
Join date : 2016-01-29

Back to top Go down

One for the Gunsmith's Empty Re: One for the Gunsmith's

Post by vmax606 10/4/2018, 8:53 am

10sandxs wrote:Jon, Where do you get 0.203 pins?  They might come in handy every now and then...

EGW.

vmax606

Posts : 12
Join date : 2018-06-05

Back to top Go down

One for the Gunsmith's Empty Re: One for the Gunsmith's

Post by Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum