New Project
+3
Dcforman
Jon Eulette
Tim:H11
7 posters
Page 1 of 1
Tim:H11- Posts : 2133
Join date : 2015-11-04
Age : 36
Location : Midland, GA
jglenn21 and chiz1180 like this post
Re: New Project
Go for it!
Jon
Jon
Jon Eulette- Posts : 4399
Join date : 2013-04-15
Location : Southern Kalifornia
Re: New Project
I still haven’t found the killer load for this one but I’m not in a hurry either.
Tim:H11- Posts : 2133
Join date : 2015-11-04
Age : 36
Location : Midland, GA
Re: New Project
Drill it, man. Just do it.
Dave
Dave
Dcforman- Posts : 928
Join date : 2017-11-18
Age : 43
Location : Ohio
Re: New Project
zanemoseley wrote:OMM?
Yup
Tim:H11- Posts : 2133
Join date : 2015-11-04
Age : 36
Location : Midland, GA
Re: New Project
Will you be able to thumb with those grips, are they Herrets? You'll do well.
Stan
Stan
chopper- Posts : 820
Join date : 2013-10-30
Age : 72
Location : Western Iowa
Re: New Project
Are the clamp on type mounts any good?
Merick- Posts : 453
Join date : 2015-08-13
Location : Kansas
Re: New Project
chopper wrote:Will you be able to thumb with those grips, are they Herrets? You'll do well.
Stan
I’ve been dry firing it some. The grips will work fine for the crazy single action shooting I do
Tim:H11- Posts : 2133
Join date : 2015-11-04
Age : 36
Location : Midland, GA
Re: New Project
Merick wrote:Are the clamp on type mounts any good?
The “base” is an old weaver base. It uses a screw that goes through the base and into the hole that the rear sight used. The front is a crescent sort of ring that is screwed to the base. When the screw is secure it pulls on the crescent piece firming it all up. It’ll be for low powered .38 Special ammunition so I don’t fear any issues with it coming loose. A base screwed directly to the frame with two or three screws would probably be better but this was a way I could do it without needing to drill any extra holes. It’s an old outdated base. The rings are stock ultradot. If this thing shoots okay, I may upgrade the rings. The base is my worry at the moment. Even with good Ammo I and suspicious of the base lending itself to good accuracy. Time will tell..
Tim:H11- Posts : 2133
Join date : 2015-11-04
Age : 36
Location : Midland, GA
Re: New Project
I used that type of Weaver clamp-on base on my K38's for years. It worked perfect for 148 HBWC target loads.
I finally got over my "collectors squeamish-ness" and had the frame drilled and tapped for the standard (on later models) 3 hole pattern under the rear sight. This allowed me to use the simpler type of later bases. There was no improvement in accuracy or reliability though.
I finally got over my "collectors squeamish-ness" and had the frame drilled and tapped for the standard (on later models) 3 hole pattern under the rear sight. This allowed me to use the simpler type of later bases. There was no improvement in accuracy or reliability though.
Black_Talon- Posts : 214
Join date : 2011-06-10
Location : SoCal
Tim:H11 likes this post
Similar topics
» 1911 Project Under Way
» New Project!!
» New Project in the works
» Project 1911 Gun
» Evolution of the 52 project
» New Project!!
» New Project in the works
» Project 1911 Gun
» Evolution of the 52 project
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum