Hornady "One Shot" NH Case Polish
+3
DavidR
Virgil Kane
Rob Kovach
7 posters
Page 1 of 1
Hornady "One Shot" NH Case Polish
I like my brass to look super shiny when I reload. I use the red tumbling media, but the stuff is super dusty. I get dust buildup in my Dillon primer slide, and dust all over my press, floor, bench. If I don't wear a dust mask, I choke on the dust when I sift the brass out.
I tried some Hornady "One Shot" case polish and added it to the media according to the instructions, and not only did it do a better job of shining up my brass, but the dust is gone, there is no residue left behind on the brass, and there is no mess. It did what it said it would, but I will never tumble again without it!
I save so much time by not having to clean the residue out of my press. THANK YOU HORNADY ONE SHOT!!
I tried some Hornady "One Shot" case polish and added it to the media according to the instructions, and not only did it do a better job of shining up my brass, but the dust is gone, there is no residue left behind on the brass, and there is no mess. It did what it said it would, but I will never tumble again without it!
I save so much time by not having to clean the residue out of my press. THANK YOU HORNADY ONE SHOT!!
Rob Kovach- Admin
- Posts : 2692
Join date : 2011-06-14
Age : 51
Location : Brooklyn, WI
Re: Hornady "One Shot" NH Case Polish
I went to SS pins three years ago and will never look back.
YMMV
Virgil
YMMV
Virgil
Virgil Kane- Posts : 574
Join date : 2011-06-10
Re: Hornady "One Shot" NH Case Polish
any good liquid car wax will do a good job added to your corn cob or crushed shells
DavidR- Admin
- Posts : 3032
Join date : 2011-06-10
Age : 70
Location : NRA:Expert, Georgia
Re: Hornady "One Shot" NH Case Polish
that's what works for me...DavidR wrote:any good liquid car wax will do a good job added to your corn cob or crushed shells
and, adding one of those used up dryer static sheets...
james r chapman- Admin
- Posts : 6372
Join date : 2012-01-31
Age : 75
Location : HELL, Michigan
Re: Hornady "One Shot" NH Case Polish
Dillon Rapid Polish and drier sheets for me. NuFinish car polish is what I hear recommended most often.
Guest- Guest
Hornady one shot case polish
Since we're on the subject of case polishing. I have heard that polishes or cleaners containing ammonia should not be used for case cleaning. Is this true and if so why?
Thanks
Thanks
Pat Nemes- Posts : 46
Join date : 2013-11-07
Location : Michigan
Re: Hornady "One Shot" NH Case Polish
something about a chemical reaction between the ammonia and the brass that makes the brass more likely to split.
Rob Kovach- Admin
- Posts : 2692
Join date : 2011-06-14
Age : 51
Location : Brooklyn, WI
Re: Hornady "One Shot" NH Case Polish
X2! If you go the SS route make sure you get the 3000rpm model. Much faster process than the standard 1500rpm model.Virgil Kane wrote:I went to SS pins three years ago and will never look back.
YMMV
Virgil
Over time I would get gunk build up on the press with the polishes.
MarkS- Posts : 30
Join date : 2011-06-11
Location : NC
Re: Hornady "One Shot" NH Case Polish
Where do you get SS pins?
Rob Kovach- Admin
- Posts : 2692
Join date : 2011-06-14
Age : 51
Location : Brooklyn, WI
Re: Hornady "One Shot" NH Case Polish
It is a totally different cleaning system that uses the stainless steel media, water, Dawn and a dash of Lemi-Shine. Most use the Thumbler Tumbler Model B (high speed- 3000 rpm).
Use can read about it at the link below, it actually does get your brass that clean in 1 1/2 - 2 hours.
http://www.stainlesstumblingmedia.com/
Use can read about it at the link below, it actually does get your brass that clean in 1 1/2 - 2 hours.
http://www.stainlesstumblingmedia.com/
MarkS- Posts : 30
Join date : 2011-06-11
Location : NC
Re: Hornady "One Shot" NH Case Polish
polish alert. Do not use polishes containing amonia for cleaning brass to be shot. amonia makes brass brittle and prone crack or worse fail at base. I was a class 06 ammo mfg. for 20 yrs.
Steve
Steve
SPAShooting- Posts : 4
Join date : 2012-07-25
Similar topics
» Hornady PTX Case Mouth Expander
» Wet polish process
» Hornady .45s available in qty
» Low First Shot
» First shot of the day
» Wet polish process
» Hornady .45s available in qty
» Low First Shot
» First shot of the day
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum