Source for .32 wad cutter projectiles
+4
Ghillieman
Bullseye58
LenV
paulmcallister
8 posters
Page 1 of 1
Source for .32 wad cutter projectiles
Hello, I want to start loading. 32 S&W for my Walther and I'm looking for projectile and supplier recommendations. Thanks.
paulmcallister- Posts : 32
Join date : 2015-06-07
Re: Source for .32 wad cutter projectiles
http://www.pennbullets.com/32/32-caliber.html
or [url=http://magnusbullets.com/images/bullet photos/image201.jpg]http://magnusbullets.com/images/bullet%20photos/image201.jpg[/url]
And my personal favorite http://tbbullets.com/
Len
or [url=http://magnusbullets.com/images/bullet photos/image201.jpg]http://magnusbullets.com/images/bullet%20photos/image201.jpg[/url]
And my personal favorite http://tbbullets.com/
Len
LenV- Posts : 4768
Join date : 2014-01-24
Age : 74
Location : Oregon
Re: Source for .32 wad cutter projectiles
Good to know Sir, ty.
Bullseye58- Posts : 125
Join date : 2012-05-25
Re: Source for .32 wad cutter projectiles
I will be casting some up for my 32 wadcutter. If there is enough demand I was looking at getting a type 6 FFL to make and sell them.
Ghillieman- Posts : 468
Join date : 2012-02-14
Location : TEXAS
Re: Source for .32 wad cutter projectiles
Question for the 32 wadcutter shooters......
What is the bore diameter in your pistol?
What sized diameter bullet would you like to have?
What is the bore diameter in your pistol?
What sized diameter bullet would you like to have?
Ghillieman- Posts : 468
Join date : 2012-02-14
Location : TEXAS
Re: Source for .32 wad cutter projectiles
Greetings,
The Walther GSP-C pistols generally have groove diameters 0.313"-0.314".
Ten ring groups can be had using the 0.314" H&N 100 grain Match Greased HBWC loaded in Lapua cases with 1.7 grains of Bullseye powder.
It helps to have an expander plug of 0.315" the length of the bullet to expand the case for a nice interference fit. 0.315" is not a typo. It allows for the spring back.
H&N bullets are available from Canada...
Cibles Canada Targets
181 St-Henri
Gatineau ( Hull ), QC
J8X 4J6
Tel. 819-778-8857
Fax. 819-778-2647
Web www.targets.ca
EBAY http://stores.shop.ebay.ca/Olympic-marksman-equipment
Visa, MasterCard, Paypal accepted
Business hours Monday to Friday 8:30 am to 4:00pm
If you chose to shoot cast bullets, look for them sized 0.314" and use Lapua cases and 1.6 grains of Winchester WST powder.
Keep the bore/throat area clean. It fouls up quickly and accuracy diminishes.
Cheers,
Dave
The Walther GSP-C pistols generally have groove diameters 0.313"-0.314".
Ten ring groups can be had using the 0.314" H&N 100 grain Match Greased HBWC loaded in Lapua cases with 1.7 grains of Bullseye powder.
It helps to have an expander plug of 0.315" the length of the bullet to expand the case for a nice interference fit. 0.315" is not a typo. It allows for the spring back.
H&N bullets are available from Canada...
Cibles Canada Targets
181 St-Henri
Gatineau ( Hull ), QC
J8X 4J6
Tel. 819-778-8857
Fax. 819-778-2647
Web www.targets.ca
EBAY http://stores.shop.ebay.ca/Olympic-marksman-equipment
Visa, MasterCard, Paypal accepted
Business hours Monday to Friday 8:30 am to 4:00pm
If you chose to shoot cast bullets, look for them sized 0.314" and use Lapua cases and 1.6 grains of Winchester WST powder.
Keep the bore/throat area clean. It fouls up quickly and accuracy diminishes.
Cheers,
Dave
fc60- Posts : 1458
Join date : 2011-06-11
Location : South Prairie, WA 98385
Re: Source for .32 wad cutter projectiles
HN can be bought from roco, also larrys guns carries some accurate speer wad cutters. we found these to be vey accurate
http://www.larrysguns.com/Products/Speer-38-Spec-148gr-HBWC--Match__Speer-spc-38-spc-Spec-prd--spc-148gr-prd--spc-HBWC-comm--spc-Match.aspx
http://www.larrysguns.com/Products/Speer-38-Spec-148gr-HBWC--Match__Speer-spc-38-spc-Spec-prd--spc-148gr-prd--spc-HBWC-comm--spc-Match.aspx
DavidR- Admin
- Posts : 3032
Join date : 2011-06-10
Age : 70
Location : NRA:Expert, Georgia
Re: Source for .32 wad cutter projectiles
Contact Bob Palermo over at Penn Bullets. Bob makes a high quality product and is very knowledgeable on reloading.
http://www.pennbullets.com/32/32-caliber.html
http://www.pennbullets.com/32/32-caliber.html
AllAces- Posts : 745
Join date : 2011-08-30
Re: Source for .32 wad cutter projectiles
fc60 wrote:Greetings,
Ten ring groups can be had using the 0.314" H&N 100 grain Match Greased HBWC loaded in Lapua cases with 1.7 grains of Bullseye powder.
Dave
Hi Dave, I have searched the WEB and can't find a supplier for the H&N. Could you point me in the right direction
paulmcallister- Posts : 32
Join date : 2015-06-07
Re: Source for .32 wad cutter projectiles
Hello everyone, I have a couple more questions.
For Bullseye shooting do the projectiles need to be swaged?
What do I need to be doing/frequency for keeping the barrel clean of lead fouling?
Thanks so much for the replies.
Paul
For Bullseye shooting do the projectiles need to be swaged?
What do I need to be doing/frequency for keeping the barrel clean of lead fouling?
Thanks so much for the replies.
Paul
paulmcallister- Posts : 32
Join date : 2015-06-07
Re: Source for .32 wad cutter projectiles
H&N bullets are available from Canada...
Cibles Canada Targets
181 St-Henri
Gatineau ( Hull ), QC
J8X 4J6
Tel. 819-778-8857
Fax. 819-778-2647
Web www.targets.ca
They do ship to the US
Cibles Canada Targets
181 St-Henri
Gatineau ( Hull ), QC
J8X 4J6
Tel. 819-778-8857
Fax. 819-778-2647
Web www.targets.ca
They do ship to the US
dhenry132- Posts : 77
Join date : 2014-02-09
Location : Republic of Texas
Re: Source for .32 wad cutter projectiles
Bad News.
I got an email from Jocelyn Langois of Cibles...
"we have received very little quantity due to the German new law, for exporting bullet of all kind. We need to apply for special license. We have in stock the .311, 312, 313."
It may be a while before the 0.314" bullets return.
Cheers,
Dave
I got an email from Jocelyn Langois of Cibles...
"we have received very little quantity due to the German new law, for exporting bullet of all kind. We need to apply for special license. We have in stock the .311, 312, 313."
It may be a while before the 0.314" bullets return.
Cheers,
Dave
fc60- Posts : 1458
Join date : 2011-06-11
Location : South Prairie, WA 98385
Similar topics
» 38 SWC with DEWC projectiles.
» Molds for casting SWC projectiles
» Sealing primers (and projectiles), do you and if so with what product?
» Demilled projectiles, are they ok for bullseye or appropriate only for plinking?
» HiTek coated projectiles...in your experience, are they as accurate as the Hornady JHP or the Zero JHP-C?
» Molds for casting SWC projectiles
» Sealing primers (and projectiles), do you and if so with what product?
» Demilled projectiles, are they ok for bullseye or appropriate only for plinking?
» HiTek coated projectiles...in your experience, are they as accurate as the Hornady JHP or the Zero JHP-C?
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum