Bullseye-L Forum
Would you like to react to this message? Create an account in a few clicks or log in to continue.

H208 rear sight blade needed

4 posters

Go down

H208 rear sight blade needed Empty H208 rear sight blade needed

Post by bruce martindale 8/5/2019, 2:04 pm

Here's an uh-oh; went to shoot iron sights and discovered no rear sight blade present.

I am guessing that it got bumped somewhere and the blade sprung loose.

Anyone have a spare they can part with?

Anyone hane Hendersons email? Hendo something...

Anyone know the dimensions so I can afapt or make one?

Thanks in advance!

bruce martindale

Posts : 1744
Join date : 2011-07-29
Location : Upstate NY

https://www.bullseyeforum.net/t20747-feeling-center-a-10-bullsey

Back to top Go down

H208 rear sight blade needed Empty Re: H208 rear sight blade needed

Post by Steve Brown 8/8/2019, 12:32 am

Neal at I.S.S. has/had some H208 parts.  I bought a 208 rear sight blade from him a couple years ago.

You probably already know it is best to call.  817 595-2090.

Steve Brown

Posts : 33
Join date : 2011-06-10
Location : Pacific Northwest

Back to top Go down

H208 rear sight blade needed Empty Re: H208 rear sight blade needed

Post by TonyH 8/8/2019, 6:12 am

Jim Henderson contact info here:
https://www.thecardinalcenter.com/contact
TonyH
TonyH

Posts : 802
Join date : 2018-08-06
Location : Utah's Dixie

Back to top Go down

H208 rear sight blade needed Empty Re: H208 rear sight blade needed

Post by Ed Hall 8/8/2019, 9:11 am

Here are some rough measurements with a cheap set of calipers.  Note that the front of the sight has a slightly wider opening and shorter height so that the edges toward the eye are sharp.  I did not measure this bevel.  These measurements are of a 3.2 mm sight blade.

H208 rear sight blade needed 208rsi10

Ed Hall

Posts : 1090
Join date : 2012-09-10
Location : Adirondack Mountains

http://www.starreloaders.com/edhall/

Back to top Go down

H208 rear sight blade needed Empty Re: H208 rear sight blade needed

Post by bruce martindale 8/8/2019, 9:55 pm

Thanks all, and especially to Ed who measured his.
I have one on order from Neil Stepp at ISS in Ft Worth Texas.

We get lazy with our vocabulary; the H208 sight blade is not the same as the 208s that l have. Neil caught it and I am confident the right part will come. I assume that the blade comes out by pushing sideways and lifting? Maybe it just pops straight back down to replace?

bruce martindale

Posts : 1744
Join date : 2011-07-29
Location : Upstate NY

https://www.bullseyeforum.net/t20747-feeling-center-a-10-bullsey

Back to top Go down

H208 rear sight blade needed Empty Re: H208 rear sight blade needed

Post by Steve Brown 8/8/2019, 11:20 pm

bruce martindale wrote: I assume that the blade comes out by pushing sideways and lifting? Maybe it just pops straight back down to replace?

Yes, the serrations on the side of the sight blade are there to lever the blade up and out.  The Hammerli tool has a notch to do it.  Yes, it pops straight back down into the slot.  At least that is how it is on my H208s.

Steve Brown

Posts : 33
Join date : 2011-06-10
Location : Pacific Northwest

Back to top Go down

H208 rear sight blade needed Empty Re: H208 rear sight blade needed

Post by Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum