Bullseye-L Forum
Would you like to react to this message? Create an account in a few clicks or log in to continue.

What's your favorite 9mm load for 1:10 barrels?

5 posters

Go down

What's your favorite 9mm load for 1:10 barrels? Empty What's your favorite 9mm load for 1:10 barrels?

Post by zanemoseley Thu Feb 20, 2020 1:34 pm

Both my P210A and my Accushadow have 1:10 barrels. I had (500) 115gr XTP bullets from a Hornady rebate I've loaded, initial impressions were that it was pretty darn snappy when loaded with 6.0gr of Power Pistol which should be about 1150fps. I'm thinking of going with 125gr conical or 147gr JHP both made by Zero, I've heard some of you guys say the heavier/slower bullets feel less snappy but not sure which is going to cooperate with the twist rate I've got. What do you guys recommend?

zanemoseley

Posts : 2688
Join date : 2015-07-11
Location : Cookeville, TN

Back to top Go down

What's your favorite 9mm load for 1:10 barrels? Empty Re: What's your favorite 9mm load for 1:10 barrels?

Post by JIMPGOV Thu Feb 20, 2020 2:47 pm

4.2GR VV330 OR 4.0GR WSF + HORNADY XTP 147GR. THE ZEROS ARE NOT AS TIGHT AT 50YDS.

JIMPGOV

Posts : 657
Join date : 2011-09-27

Back to top Go down

What's your favorite 9mm load for 1:10 barrels? Empty Re: What's your favorite 9mm load for 1:10 barrels?

Post by zanemoseley Thu Feb 20, 2020 3:50 pm

Too bad the 147 XTP bullets are $.20 each, the Zero can be had for about $.10 especially if I buy from Terry at a match.

zanemoseley

Posts : 2688
Join date : 2015-07-11
Location : Cookeville, TN

Back to top Go down

What's your favorite 9mm load for 1:10 barrels? Empty Re: What's your favorite 9mm load for 1:10 barrels?

Post by Dcforman Thu Feb 20, 2020 4:00 pm

Maplewood 105 gr LSWC (mini H&G 68 clone), 2.5 WST, 1.035" OAL (I think?), 0.372 crimp, in a really sprung down CZ75 SP01 with a slide mount H1. Feels just slightly more recoil than a 22. No idea on velocity. Groups an inch at 25, need to do more testing at 50 when the weather warms up!

Dave

Dcforman

Posts : 928
Join date : 2017-11-18
Age : 43
Location : Ohio

Back to top Go down

What's your favorite 9mm load for 1:10 barrels? Empty Re: What's your favorite 9mm load for 1:10 barrels?

Post by tovaert Thu Feb 20, 2020 8:33 pm

P210A: 147gr Hornady XTPs w/3.3gr of Alliant e^3, Fed 100 primers, Starline brass (Note: I use a 16# CZ P-01 recoil spring from CGW). Very good groups from a Ransom rest at 50 yards. This winter (indoors) I've been shooting 147gr Brazos CRNs with *FC* brass, Fed 100 primers, 3.3gr of WSF (I had an extra pound I wanted to use up), about 880 fps MV. I think 900 fps +/- is good for this pistol. In spring I'll start testing the Zero 147 JHPs at 50 yards, and the Brazos 147 CRNs at 25 yards. I tried 115gr XTPs...but I've decided to just stick with 147's.

tovaert

Posts : 455
Join date : 2018-11-28

Back to top Go down

What's your favorite 9mm load for 1:10 barrels? Empty Re: What's your favorite 9mm load for 1:10 barrels?

Post by Mac2 Mon Mar 02, 2020 2:29 pm

Reliable in several twist-deficient pistols:  3.7 grains of WSF and 147 P-Delta truncated-point at 1.13 OAL.  (OAL is from memory).  Both Federal match and CCI primers work. 
Cases are run through SS pin treatment - very clean.

Mac2

Posts : 188
Join date : 2015-04-09
Location : LP Michigan

Back to top Go down

What's your favorite 9mm load for 1:10 barrels? Empty Re: What's your favorite 9mm load for 1:10 barrels?

Post by Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum