Bullseye-L Forum
Would you like to react to this message? Create an account in a few clicks or log in to continue.

Model 41 issue

+2
Steve K
funski
6 posters

Go down

Model 41 issue Empty Model 41 issue

Post by funski 1/14/2022, 7:17 am

Have an older model 41 with a Clark Barrel.  First round in chamber,  pull the trigger and nothing,  no click, no hammer fall, no mark from firing pin.  I have turned out the over travel screw to a non-issue point.  Doesn't happen all the the time.  I can clear chamber and repeat and it works fine or not.  Very frustrating and am tired of the alibies.   Any help, suggestions would be greatly appreciated.  
Thanks in advance
Jim

funski

Posts : 48
Join date : 2021-01-07

Back to top Go down

Model 41 issue Empty Re: Model 41 issue

Post by Steve K 1/14/2022, 10:39 am

I've found a good cleaning stops most of the 41 problems I've had. I scrub with Acitone and finish off with a bath in the sonic cleaner using a small amount of Dawn; works well.

Steve K

Posts : 189
Join date : 2015-11-09

Back to top Go down

Model 41 issue Empty Re: Model 41 issue

Post by WesG 1/14/2022, 11:33 am

I pull the slide back a bit to drop the hammer before putting the gun away. Cant pull it very far before the trigger is disconnected. So maybe it's not closing completely, and/or theres some wear or tolerance issue with the parts.

Another potential issue could be the barrel itself. It seats in the frame at the front of the lug. If that's out of tolerance, or its somehow crudded up, the breech face could be further back, holding the slide at the borderline of function.


Last edited by WesG on 1/14/2022, 5:38 pm; edited 1 time in total

WesG

Posts : 713
Join date : 2018-09-21
Location : Cedar Park, TX - N CA

Slamfire likes this post

Back to top Go down

Model 41 issue Empty Re: Model 41 issue

Post by Ed Hall 1/14/2022, 4:58 pm

Writing from memory, so correct me someone, if I err, but I'm pretty sure you can pull the right grip panel and see how far the trigger bar engages the sear arm.  It should go the full depth of the shoulder.  If it isn't, check the magazine disconnector, if equipped, and then look for other reasons if that's OK.  It could also be a broken (or weakened) trigger bar spring.

Ed Hall

Posts : 1090
Join date : 2012-09-10
Location : Adirondack Mountains

http://www.starreloaders.com/edhall/

Slamfire likes this post

Back to top Go down

Model 41 issue Empty Re: Model 41 issue

Post by WesG 1/14/2022, 5:57 pm

Correct.

Model 41 issue 20220110
Model 41 issue 20220111

WesG

Posts : 713
Join date : 2018-09-21
Location : Cedar Park, TX - N CA

Back to top Go down

Model 41 issue Empty Re: Model 41 issue

Post by Ironarmknives 1/15/2022, 5:36 am

Most disappointing gun I’ve ever bought couldn’t get five magazines through it will not fire fires but misfires returned it dream of a lifetime didn’t even have it for a day what a shame piece of crap just saying ,1300.00 it should work right ammo ,worked great 2 mag’s then started misfiring ,cleaned great for two shots then misfires ,my last attempt went two magazines no fire I returned it almost crying but I did return it never buy another

Ironarmknives

Posts : 45
Join date : 2020-01-28

Back to top Go down

Model 41 issue Empty Re: Model 41 issue

Post by funski 1/15/2022, 8:13 am

Is there any gunsmith out there I can send it to for repairs?  
I prefer not to send it to Clark unless I have no choice. 

Thanks in advance ----Again
Jim

funski

Posts : 48
Join date : 2021-01-07

Back to top Go down

Model 41 issue Empty Re: Model 41 issue

Post by hamdenman 1/15/2022, 10:46 am

KC Crawford would be my choice. He’s a sponsor on this sight as well. Heck of a good guy.

hamdenman

Posts : 210
Join date : 2012-09-07

Outthere and Dockokol like this post

Back to top Go down

Model 41 issue Empty Re: Model 41 issue

Post by Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum