Bullseye-L Forum
Would you like to react to this message? Create an account in a few clicks or log in to continue.
Bullseye-L Forum

A Forum dedicated to the sport of Bullseye shooting


High Standard extractor

+3
Coupebuilder
kc.crawford.7
Nopro
7 posters

Bullseye-L Forum :: Equipment Discussion

Go down

High Standard extractor Empty High Standard extractor

Post by Nopro Mon Feb 14, 2022 12:19 am

Where's the best place to order extractor parts for my Hamden High Standard Citation Military 22lr pistol?

Nopro

Posts : 61
Join date : 2020-05-08

Back to top Go down

High Standard extractor Empty Re: High Standard extractor

Post by kc.crawford.7 Mon Feb 14, 2022 5:05 am

High Standard of Montana
kc.crawford.7
kc.crawford.7

Posts : 736
Join date : 2012-12-09
Location : Maysville, NC

http://www.kcskustomcreations.com

Back to top Go down

High Standard extractor Empty Re: High Standard extractor

Post by Coupebuilder Mon Feb 14, 2022 8:36 am

I have most late model parts in NOS if youre looking for later model like the citation. PM me with part numbers or description. I have plungers, springs and new extractors

Coupebuilder

Posts : 128
Join date : 2021-10-20

Back to top Go down

High Standard extractor Empty Re: High Standard extractor

Post by chopper Mon Feb 14, 2022 8:45 am

Take the slide off the gun and clean the recess on the bolt face where cartridge fits under the extractor. Slide a cartridge under extractor and give the slide a little shake, it should stay under the extractor.
 Ideally the extractor should contact at the corner or junction of the case side and rim.
 More than likely you might have to tune or adjust the extractor to grab the rim of the case.
 Stan

chopper

Posts : 820
Join date : 2013-10-29
Age : 72
Location : Western Iowa

Back to top Go down

High Standard extractor Empty Re: High Standard extractor

Post by NukeMMC Mon Feb 14, 2022 10:55 am

Volquartsen made Exact Edge extractors for HS for a while.  Their website shows it as discontinued.  I may still have 1 or 2.  As KC said, HSInc in Montana or Interarms in Tx have HS parts.  Interarms website has extractors at $9
NukeMMC
NukeMMC

Posts : 564
Join date : 2018-10-12

Back to top Go down

High Standard extractor Empty Re: High Standard extractor

Post by Nopro Mon Feb 14, 2022 3:23 pm

Is the extractor the same across the HS product line (the Victor, Trophy & Citation)?

Nopro

Posts : 61
Join date : 2020-05-08

Back to top Go down

High Standard extractor Empty Re: High Standard extractor

Post by NukeMMC Mon Feb 14, 2022 3:37 pm

Yes. And 103-107
NukeMMC
NukeMMC

Posts : 564
Join date : 2018-10-12

Back to top Go down

High Standard extractor Empty Re: High Standard extractor

Post by wealth212 Fri Feb 25, 2022 5:45 am

Nopro wrote:Where's the best place to order extractor parts for my Hamden High Standard Citation Military 22lr pistol?

You can check on ebay, i saw it listed there few days ago.

wealth212

Posts : 16
Join date : 2022-01-04

Back to top Go down

High Standard extractor Empty Re: High Standard extractor

Post by Capt Jack Thu Feb 15, 2024 12:29 pm

I need a High Standard Mk iv 22 WMR extractor
will other HS 22 WMR model extractors work?

Capt Jack

Posts : 1
Join date : 2024-02-15

Back to top Go down

High Standard extractor Empty Re: High Standard extractor

Post by Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

Bullseye-L Forum :: Equipment Discussion

 
Permissions in this forum:
You cannot reply to topics in this forum