I need some help identifying this piece.
+3
NukeMMC
Drawman623
Multiracer
7 posters
Page 1 of 1
Multiracer- Posts : 999
Join date : 2017-03-15
Location : North Ohio
Re: I need some help identifying this piece.
Definitely Kart mags.
Barrel crown and retainer logo are Kart too
Barrel crown and retainer logo are Kart too
Drawman623- Posts : 115
Join date : 2021-11-28
Re: I need some help identifying this piece.
Looks like the Kart rifling. Wasn't it Marlin Micro-groove?
NukeMMC- Posts : 564
Join date : 2018-10-12
Re: I need some help identifying this piece.
What you have looks like a Kart. The one piece slide stop is what they came with. The two piece is like a Nelson slide stop.
If it has no markings could it be an early version or prototype? Or maybe a previous owner polished the markings off and refinished.
The original markings were not very deep.
It also looks like someone changed the rib for scope rings or removed the sights to install rings.
Darrell
If it has no markings could it be an early version or prototype? Or maybe a previous owner polished the markings off and refinished.
The original markings were not very deep.
It also looks like someone changed the rib for scope rings or removed the sights to install rings.
Darrell
djperry2- Posts : 103
Join date : 2018-04-07
Age : 68
Re: I need some help identifying this piece.
Is the rib integral to the top shroud? Not screwed on, but actually machined as one piece? Then you have a Dworak conversion, because (in my knowledge) that's exactly how his conversion differed from Kart.
Tripscape- Posts : 878
Join date : 2019-03-23
Allan Campbell likes this post
Re: I need some help identifying this piece.
The rib looks like an older Weaver aluminum rib fastened to the top of the slide with three fasteners.Tripscape wrote:Is the rib integral to the top shroud? Not screwed on, but actually machined as one piece? Then you have a Dworak conversion, because (in my knowledge) that's exactly how his conversion differed from Kart.
Multiracer- Posts : 999
Join date : 2017-03-15
Location : North Ohio
Re: I need some help identifying this piece.
It's a Kart. The Dworak conversion shroud had a pic rail built into it.
Outthere and Multiracer like this post
Re: I need some help identifying this piece.
Thank you KC, that's exactly what I was looking for , a positive ID.
Multiracer- Posts : 999
Join date : 2017-03-15
Location : North Ohio
Outthere likes this post
Re: I need some help identifying this piece.
So, I did some more disassembly. The rail is integral to the slide, the fasteners hold the barrel in position, the other parts are shown. There is a .22LR marking and a number 2727 marking.
Multiracer- Posts : 999
Join date : 2017-03-15
Location : North Ohio
Multiracer- Posts : 999
Join date : 2017-03-15
Location : North Ohio
Multiracer- Posts : 999
Join date : 2017-03-15
Location : North Ohio
Multiracer- Posts : 999
Join date : 2017-03-15
Location : North Ohio
Re: I need some help identifying this piece.
I'd say its a Kart with a Dworack aluminum shroud. Looks just like mine. A lot of us replaced the Kart steel slide with the aluminum shroud to get rid of some weight back in the day. By the way, it is not a one piece slide stop pin as someone mentioned. A little screw attaches the lever portion to the pin part. If you look closely at the picture, you can see the little screw.
Phil
Phil
PMcfall- Posts : 395
Join date : 2011-06-16
Location : St. Joseph, MO
Multiracer likes this post
Similar topics
» Identifying Old 1” Red Dot
» Help identifying some parts...
» A little help identifying grips
» Need help identifying a grip
» Identifying powder
» Help identifying some parts...
» A little help identifying grips
» Need help identifying a grip
» Identifying powder
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum