load Questions
+2
gulliver62
Paper-Puncher
6 posters
Page 1 of 1
load Questions
with things looking up on my kimber ......I need some advice on laods....I have clays and 700x on hand . Shold I use a 200gr Lswc or a 230 gr LRN ..lookin for a nice soft load for indoor 25yd shooting any advice?
Paper-Puncher- Posts : 321
Join date : 2011-09-22
Age : 59
Location : Ohio
Re: load Questions
I can't help with those powders but heavy bullets don't equal nice soft load.
For a soft load, I would go down to 185 or even 165 either of which you can get to group very well at 25 yd. I shoot 185g with 4.0 bullseye behind it at 25yd. I was shooting as low as 3.7 but the group tightens up with 4.0.
For hardball, I am shooting 230g with 3.8 BE behind it to get the recoil down.
For a soft load, I would go down to 185 or even 165 either of which you can get to group very well at 25 yd. I shoot 185g with 4.0 bullseye behind it at 25yd. I was shooting as low as 3.7 but the group tightens up with 4.0.
For hardball, I am shooting 230g with 3.8 BE behind it to get the recoil down.
gulliver62- Posts : 106
Join date : 2011-10-27
Location : Atlanta, GA
Re: load Questions
Soft accurate load, 160 grain w/4.5 grains of Bullseye, clays or V-n-310.
DavidR- Admin
- Posts : 3032
Join date : 2011-06-10
Age : 70
Location : NRA:Expert, Georgia
Re: load Questions
185swc over 3.8 Bullseye for 25yd line or less
Rob Kovach- Admin
- Posts : 2692
Join date : 2011-06-13
Age : 51
Location : Brooklyn, WI
Re: load Questions
which bullet.....??????
Paper-Puncher- Posts : 321
Join date : 2011-09-22
Age : 59
Location : Ohio
Re: load Questions
If you mean which of the ones you mentioned in your first post - the 200gr SWC. If you mean which 185gr SWC mentioned in the previous post it doesn't matter. Any one will shoot fine at 25 yards. Most of the commercial casters have a 185gr SWC in their lineup and most are shaped like the H&G 68 - easier for you to Google that than for me to explain it. Load them over 3.5gr of your clays and go shoot. Seat them till about 1/32" of shoulder is showing past the case mouth, about .930 from the back of the case to the shoulder. With your barrel OUT of the gun make sure this length lets the loaded round sit slightly below the hood. Good luck - Dan
dan allen- Posts : 118
Join date : 2011-06-19
Location : Distinguished - 2600 Club
Re: load Questions
3.5gr of Clays? I may have to try that as I set up my new Lee 1000 Pro. I was trying to get down to 3.7 with my Dillon but it did not meter well and loads were 3.4 - 4gr!
Joe
Joe
Similar topics
» Goodbye Hornady 0.311" 60 Grain XTP
» 9mm service pistol load questions
» Load work up / loading questions, first pistol rounds in 10 years.
» Load question on Penn Bullets for Distinguished load
» Hornady Lock-N-Load AP vs Lee Load Master
» 9mm service pistol load questions
» Load work up / loading questions, first pistol rounds in 10 years.
» Load question on Penn Bullets for Distinguished load
» Hornady Lock-N-Load AP vs Lee Load Master
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum