Tuning High Standard Magazines
5 posters
Page 1 of 1
Tuning High Standard Magazines
Which magazine tuning tool do you prefer for adjusting the lips on a High Standard Magazine? I have the silver one with one slot for gripping and the other end is used as a starting reference. It can be purchased on Amazon or EBay and it does a fair job. I just purchase a "new in the box" Hamden magazine and it will probably require some adjustment.
Looking for input on the best options.
Looking for input on the best options.
Paul M.- Posts : 37
Join date : 2017-04-26
Age : 63
Location : Riverside, CA
Re: Tuning High Standard Magazines
http://www.samscustomgunworksusa.com/partstoolsforsale.html
Chris Miceli- Posts : 2715
Join date : 2015-10-27
Location : Northern Virginia
Re: Tuning High Standard Magazines
how to instructions:
[url=http://www.highstandardpartsonline.com/High Standard Magazine Adjustments Models102-107 PTS1.pdf]www.highstandardpartsonline.com/High%20Standard%20Magazine%20Adjustments%20Models102-107%20PTS1.pdf[/url]
IĀ use this tool with good results:
https://highstandardpartsonline.com/magazine-adjustment-tool-for-high-standard-22-cal-p-13.html?cPath=3
[url=http://www.highstandardpartsonline.com/High Standard Magazine Adjustments Models102-107 PTS1.pdf]www.highstandardpartsonline.com/High%20Standard%20Magazine%20Adjustments%20Models102-107%20PTS1.pdf[/url]
IĀ use this tool with good results:
https://highstandardpartsonline.com/magazine-adjustment-tool-for-high-standard-22-cal-p-13.html?cPath=3
Last edited by jglenn21 on Tue Feb 13, 2018 11:44 pm; edited 10 times in total
jglenn21- Posts : 2620
Join date : 2015-04-07
Age : 76
Location : monroe , ga
Re: Tuning High Standard Magazines
I have the one jglenn uses and the instructions that come with it are spot on for the info you need. I have 4 thick metal magazines I've aquired over the last 5 years and they do stay in adjustment a lot longer than the others. I take em apart and clean them about every year with Eds Red then wash them with Dawn detergent and hot water blow dry with the compressor, then spray em with CLP inside and out then reassemble. Never a problem with feeding ever.
Stan
Stan
chopper- Posts : 820
Join date : 2013-10-30
Age : 72
Location : Western Iowa
Re: Tuning High Standard Magazines
The tool you have purchased does a fine job.
The rear lips are for elevation of the round and the front lips are for steering the round left and right.
The rear lips are for elevation of the round and the front lips are for steering the round left and right.
Multiracer- Posts : 998
Join date : 2017-03-16
Location : North Ohio
Re: Tuning High Standard Magazines
Thank you for your input, it's been helpful. It looks like the style tool I have is good. I had seen a few different style tools from different vendors and was just wondering if any particular one was better, so I thought I would ask some folks with a lot more experience than I've got.
Paul M.- Posts : 37
Join date : 2017-04-26
Age : 63
Location : Riverside, CA
Re: Tuning High Standard Magazines
The two stepped areas on the opposite end of the slot are your base dimensions for each pair of feed lips. They should be parallel and at the minimum as wide as the tool.
Multiracer- Posts : 998
Join date : 2017-03-16
Location : North Ohio
Re: Tuning High Standard Magazines
Thank you for all the input. I got the magazine today, never had to do anything, it works perfectly.
Paul M.- Posts : 37
Join date : 2017-04-26
Age : 63
Location : Riverside, CA
Similar topics
» High standard mag tuning woes
» High Standard Magazines
» High Standard Factory Magazines
» High Standard Help
» Tuning Model 52 Magazines
» High Standard Magazines
» High Standard Factory Magazines
» High Standard Help
» Tuning Model 52 Magazines
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum