Bullseye-L Forum
Would you like to react to this message? Create an account in a few clicks or log in to continue.

Advice needed on getting a BE 1911 in .45 acp

+5
kc.crawford.7
DavidR
cdrt
Tim:H11
Sheriff1962
9 posters

Go down

Advice needed on getting a BE 1911 in .45 acp Empty Advice needed on getting a BE 1911 in .45 acp

Post by Sheriff1962 Thu Oct 04, 2018 11:02 am

I already  have several nice 1911's  but want to have  a single stack ,  Bulls Eye 1911 with iron sights,  that will be designated only for  185/200SWC  target loads.
No hardball , no major power factor loads , no duty ammo.

I also want to start with an existing pistol ( not frame and slide set) and have it build into a BE gun.

Where would You  begin?

THANK YOU.

Sheriff1962

Posts : 176
Join date : 2018-07-04

Back to top Go down

Advice needed on getting a BE 1911 in .45 acp Empty Re: Advice needed on getting a BE 1911 in .45 acp

Post by Tim:H11 Thu Oct 04, 2018 11:13 am

On a budget, get a Springfield Range Officer and have someone like Jon rebarrel it and do the trigger. Simple.
Tim:H11
Tim:H11

Posts : 2133
Join date : 2015-11-04
Age : 36
Location : Midland, GA

Back to top Go down

Advice needed on getting a BE 1911 in .45 acp Empty Re: Advice needed on getting a BE 1911 in .45 acp

Post by cdrt Thu Oct 04, 2018 2:50 pm

Tim:H11 wrote:On a budget, get a Springfield Range Officer and have someone like Jon rebarrel it and do the trigger. Simple.
What he said.
cdrt
cdrt

Posts : 843
Join date : 2016-04-12
Location : Amarillo, Texas

Back to top Go down

Advice needed on getting a BE 1911 in .45 acp Empty Re: Advice needed on getting a BE 1911 in .45 acp

Post by DavidR Thu Oct 04, 2018 7:08 pm

No need to even rebarrel it, imo until you can out shoot its factory accuracy which in most cases is master level at least. Some will hate on this but a Les Baer concept V out of the box will outshoot anyone's,  ability that I know of. Mine shoots les that 3'' at 50 yards with handloads or factory atlanta arms, it does cost more than a range officer but not that much difference if you rebarrel and pay to  get it done right, and of course there are top quality smiths on here that can fix you up although the cost usually is much higher than a RO or a L. Baer.
DavidR
DavidR
Admin

Posts : 3032
Join date : 2011-06-10
Age : 70
Location : NRA:Expert, Georgia

Back to top Go down

Advice needed on getting a BE 1911 in .45 acp Empty Re: Advice needed on getting a BE 1911 in .45 acp

Post by kc.crawford.7 Fri Oct 05, 2018 8:36 am

Springfield Armory Range Officer.  Get a bushing fit to the factory barrel and get the trigger straightened out.  You'll go far with that set up.  And if you want a dot you can do the RRA full coverage rib to hide and support the rear of the rib on the slide.
kc.crawford.7
kc.crawford.7

Posts : 734
Join date : 2012-12-09
Location : Maysville, NC

http://www.kcskustomcreations.com

Back to top Go down

Advice needed on getting a BE 1911 in .45 acp Empty Re: Advice needed on getting a BE 1911 in .45 acp

Post by Chris Miceli Fri Oct 05, 2018 9:25 am

kc.crawford.7 wrote:Springfield Armory Range Officer.  Get a bushing fit to the factory barrel and get the trigger straightened out.  You'll go far with that set up.  And if you want a dot you can do the RRA full coverage rib to hide and support the rear of the rib on the slide.
solid advise

Chris Miceli

Posts : 2715
Join date : 2015-10-27
Location : Northern Virginia

Back to top Go down

Advice needed on getting a BE 1911 in .45 acp Empty Re: Advice needed on getting a BE 1911 in .45 acp

Post by SW-52 Fri Oct 05, 2018 7:53 pm

Chris Miceli wrote:
kc.crawford.7 wrote:Springfield Armory Range Officer.  Get a bushing fit to the factory barrel and get the trigger straightened out.  You'll go far with that set up.  And if you want a dot you can do the RRA full coverage rib to hide and support the rear of the rib on the slide.
solid advise
+1
SW-52
SW-52

Posts : 803
Join date : 2015-07-20
Age : 40

Back to top Go down

Advice needed on getting a BE 1911 in .45 acp Empty Re: Advice needed on getting a BE 1911 in .45 acp

Post by bullseye Sat Oct 06, 2018 8:41 am

If you guys keep it up, I'm going to have to buy a Springfield Range Officer.
Right now, all my 1911's are Colts.

I want another 1911...........

bullseye

Posts : 20
Join date : 2018-06-18
Age : 71
Location : Texas

Back to top Go down

Advice needed on getting a BE 1911 in .45 acp Empty Re: Advice needed on getting a BE 1911 in .45 acp

Post by Tim:H11 Sat Oct 06, 2018 9:03 am

bullseye wrote:If you guys keep it up, I'm going to have to buy a Springfield Range Officer.
Right now, all my 1911's are Colts.

I want another 1911...........

The current production colts I’ve seen are overpriced for what you get.
Tim:H11
Tim:H11

Posts : 2133
Join date : 2015-11-04
Age : 36
Location : Midland, GA

Back to top Go down

Advice needed on getting a BE 1911 in .45 acp Empty Re: Advice needed on getting a BE 1911 in .45 acp

Post by TonyH Sat Oct 06, 2018 9:04 am

If you guys keep it up, I'm going to have to buy a Springfield Range Officer.
Just do it! Twisted Evil
Quite a few of those shoot really well right out of the box without any work.....shoot it just the way it came first.
If you decide to go the barrel and slide fit, trigger job route. I would highly recommend Dave Salyer to do the work.
TonyH
TonyH

Posts : 801
Join date : 2018-08-06
Location : Utah's Dixie

Back to top Go down

Advice needed on getting a BE 1911 in .45 acp Empty Re: Advice needed on getting a BE 1911 in .45 acp

Post by Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum