Remembering to adjust sights
+11
Sa-tevp
Chris Miceli
DavidR
r_zerr
robert84010
Rob Kovach
Caster3845
LenV
Olde Pilot
Wobbley
orpheoet
15 posters
Page 2 of 2
Page 2 of 2 • 1, 2
Remembering to adjust sights
First topic message reminder :
So in the Presidents 100 I fired my first 5 rounds, looked through spotting scope, all low. I forgot to raise sights for 50 yds. Came in 107th.....Last week I did the same thing in a DR match. Same issues with dot sights. I'm curious what people do to remember. Am I the only one giving points away like this? I should mention I try to not obsess over checking my target. My best slow fires are always a surprise.
So in the Presidents 100 I fired my first 5 rounds, looked through spotting scope, all low. I forgot to raise sights for 50 yds. Came in 107th.....Last week I did the same thing in a DR match. Same issues with dot sights. I'm curious what people do to remember. Am I the only one giving points away like this? I should mention I try to not obsess over checking my target. My best slow fires are always a surprise.
orpheoet- Posts : 1054
Join date : 2014-07-29
Age : 56
Location : Berea, Oh
Re: Remembering to adjust sights
Hello all,
New Bullseye shooter here with a question. I have been shooting 50ft indoors since I don't have a long outdoor range available easily.
Here is my question. I am pretty well zeroed at 50 Ft with MatchDot II. How much elevation adjustment (inches, clicks, MOA?) should it take to get me close to zeroed at 25 yds and then at 50 yds?
Just trying to get the first couple of shots on the paper and can fine tune and document from there. If it matters, pistol is Ruger Mk III, Ultradot MatchDot II and CCI Standard Velocity ammo.
Any help appreciated...
Thanks,
Bill in Cypress, Texas
New Bullseye shooter here with a question. I have been shooting 50ft indoors since I don't have a long outdoor range available easily.
Here is my question. I am pretty well zeroed at 50 Ft with MatchDot II. How much elevation adjustment (inches, clicks, MOA?) should it take to get me close to zeroed at 25 yds and then at 50 yds?
Just trying to get the first couple of shots on the paper and can fine tune and document from there. If it matters, pistol is Ruger Mk III, Ultradot MatchDot II and CCI Standard Velocity ammo.
Any help appreciated...
Thanks,
Bill in Cypress, Texas
Steamerbill- Posts : 11
Join date : 2016-10-03
Location : Cypress, Texas U.S.A.
Re: Remembering to adjust sights
None. Ok maybe 2 clicks down for 25yd but your 50' should work for 50 yds. But just leaving it alone will put them in the 10 ring. If you do your part.
Len
Len
LenV- Posts : 4771
Join date : 2014-01-24
Age : 74
Location : Oregon
Page 2 of 2 • 1, 2
Similar topics
» When to adjust rear sights?
» Adjusting sights from 25 to 50 yards. OR adjust hold?
» Make Ammo for the Long Line, or Adjust the Sights?
» Remembering Jerry Keefer
» Why do I have to adjust my Ultradot on Different Ranges
» Adjusting sights from 25 to 50 yards. OR adjust hold?
» Make Ammo for the Long Line, or Adjust the Sights?
» Remembering Jerry Keefer
» Why do I have to adjust my Ultradot on Different Ranges
Page 2 of 2
Permissions in this forum:
You cannot reply to topics in this forum