Bullseye-L Forum
Would you like to react to this message? Create an account in a few clicks or log in to continue.

I am seeking a good load for 185gr Zero SWCHP.

+7
Boris_La
Toz35m
jglenn21
BE Mike
Wobbley
Blsi2600
usmilret
11 posters

Go down

I am seeking a good load for 185gr Zero SWCHP. Empty I am seeking a good load for 185gr Zero SWCHP.

Post by usmilret 10/27/2017, 1:21 am

Gentlemen I am asking for the privilege of standing on the shoulders of giants, your experience.  I have lost my notes when I ordered zero bullets from Roze distributors. I am looking for a good target load using 185 gr SWCHP swaged lead. I am looking for the speed and recoil spring to handle these loads.  As I understand it the speed is fairly low and will be shooting this load through a Kimber Classic Gold Match pistol with an 30 mm Ultra Dot Match Dot II on top. Any recommendations are very highly appreciated and thank you!

usmilret

Posts : 5
Join date : 2017-04-08
Location : The Old Dominion State

Back to top Go down

I am seeking a good load for 185gr Zero SWCHP. Empty Re: I am seeking a good load for 185gr Zero SWCHP.

Post by Blsi2600 10/27/2017, 2:19 am

3.3 Vectan Ba10   Win LP primer  .465 taper crimp   Zero 185gr LSWHP

This load is 100% reliable, very accurate, super clean

Springfield Mil-spec with a 10# recoil, 19# mainspring, slide mount 30mm Bushnell red dot.

Blsi2600

Posts : 158
Join date : 2013-03-26
Location : SW ILLINOIS

Back to top Go down

I am seeking a good load for 185gr Zero SWCHP. Empty Re: I am seeking a good load for 185gr Zero SWCHP.

Post by Wobbley 10/27/2017, 5:48 am

3.8 to 4.2 WST, 3.8 to 4.2 Bullseye, or 3.5 to 4.0 vihtavouri N310 should work.  The Bullseye load will be dirtier.  0.468 crimp.
Wobbley
Wobbley
Admin

Posts : 4808
Join date : 2015-02-12

Back to top Go down

I am seeking a good load for 185gr Zero SWCHP. Empty Re: I am seeking a good load for 185gr Zero SWCHP.

Post by BE Mike 10/27/2017, 6:22 am

For 50 yards, 4.0 grains of Alliant Bullseye. If your pistol will function reliably, try 3.8 grains. A 12 lbs. recoil spring should work. Taper crimp to .470".
BE Mike
BE Mike

Posts : 2589
Join date : 2011-07-29
Location : Indiana

Back to top Go down

I am seeking a good load for 185gr Zero SWCHP. Empty Re: I am seeking a good load for 185gr Zero SWCHP.

Post by jglenn21 10/27/2017, 6:36 am

I run 3.9 BE with a 10 lb recoil spring and 19 main.

468 crimp.
Very accurate bullet
jglenn21
jglenn21

Posts : 2620
Join date : 2015-04-07
Age : 76
Location : monroe , ga

Back to top Go down

I am seeking a good load for 185gr Zero SWCHP. Empty Re: I am seeking a good load for 185gr Zero SWCHP.

Post by Toz35m 10/27/2017, 8:57 am

I have been getting 1.75" groups with mixed and well used 25 yd brass with:

Zero SWCHP
5.4 BE86
Crimp= .463

You really need to test versions of loads.  I have tested loads others have posted and they do not work for me.  Take my load from above and test 5.4, 5.6, 5.8 loading 5 rounds.  If one looks good then try 10 rounds and or try 5.5 and 5.7.  I use a sandbag and 25 yd target placed at 50 yds.  The 4moa dot on the 25 yd target at 50 works really good to help you shoot from a sandbag and get good groups.

For the zero SWCHP I have discovered it will lead if you shoot it too fast. So keep it under 800fps.
Toz35m
Toz35m

Posts : 266
Join date : 2012-10-17
Location : PDX

Back to top Go down

I am seeking a good load for 185gr Zero SWCHP. Empty Re: I am seeking a good load for 185gr Zero SWCHP.

Post by Boris_La 10/27/2017, 1:50 pm

3.6gr Clays, 4.2 Titegroup
Both very accurate and reliable in CZ97B

Boris_La

Posts : 89
Join date : 2016-06-26

Back to top Go down

I am seeking a good load for 185gr Zero SWCHP. Empty Re: I am seeking a good load for 185gr Zero SWCHP.

Post by ric1911a1 10/27/2017, 2:48 pm

4.0 of Bullseye for me. They shoot well in both wad guns, the ball gun, and the 625 revolver.
ric1911a1
ric1911a1

Posts : 338
Join date : 2013-05-07
Location : Upstate NY (the good part)

Back to top Go down

I am seeking a good load for 185gr Zero SWCHP. Empty Re: I am seeking a good load for 185gr Zero SWCHP.

Post by Steve B 10/28/2017, 6:34 pm

4.0 - 4.2 gr Clays, .469 crimp, Winchester primers

Steve B

Posts : 627
Join date : 2011-06-16
Location : Elkhart, IN

Back to top Go down

I am seeking a good load for 185gr Zero SWCHP. Empty Re: I am seeking a good load for 185gr Zero SWCHP.

Post by PMcfall 11/4/2017, 6:19 am

I would suggest using 3.7-4.2 grs Bullseye or WST with .2 gr more than bullseye loads.  Test them in your pistol, it will tell you which load to use.
Phil
PMcfall
PMcfall

Posts : 395
Join date : 2011-06-16
Location : St. Joseph, MO

Back to top Go down

I am seeking a good load for 185gr Zero SWCHP. Empty Re: I am seeking a good load for 185gr Zero SWCHP.

Post by kgs113 11/18/2017, 11:56 am

Steve B wrote:4.0 - 4.2 gr Clays, .469 crimp, Winchester primers
Works for me too.  Very clean.

kgs113

Posts : 20
Join date : 2014-02-02
Location : Southern Tier NY

Back to top Go down

I am seeking a good load for 185gr Zero SWCHP. Empty Re: I am seeking a good load for 185gr Zero SWCHP.

Post by Sponsored content


Sponsored content


Back to top Go down

Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum